Support

Supporto

Questions, bug reports, a model that behaves oddly: write to apps@kiusso.net. If you can, tell me the light model, the iOS version and what you expected to happen.

Frequently asked questions

My light does not appear in the list.

Check that the light is on and close to the iPhone, and that its Bluetooth is active. Tap "Search for lights" to scan again. Another phone or app already connected to the light can prevent it from showing up: a Bluetooth light accepts one connection at a time. If the app says the light's radio firmware is older than 2.4.2, that light cannot be controlled by LightDeck.

The app says Bluetooth access is off.

Open Settings on the iPhone, find LightDeck and allow Bluetooth. The app has a button that takes you there. Also check that Bluetooth is on in Control Center.

Can I control several lights together?

No. LightDeck controls one light at a time, the one the iPhone is connected to. Lights already found stay in the list, so you can switch from one to another.

Some effects are missing.

The effects depend on the model. Mono and dual color lights have few or none; full color models have more. LightDeck shows only what the model reports as supported.

I tapped "Switch to DMX" and the light went dark.

That is expected. In DMX mode the light turns off until it receives a DMX signal. Tap "Back to Bluetooth" and the app sends the last color temperature again.

Supported models

LightDeck recognizes the LUPO models in the table of the official app: Dayled, Superpanel, Actionpanel, Kickasspanel, Ultrapanel, Hyperpanel, Lupo LED and Movielight (300 and 600). What each model offers (effects, K range, fan, DMX) comes from the same table.

Tested only on the Movielight 300 Dual Color. On the other models LightDeck should work, but it has not been tried on them. If you have one and something does not work, please write.

What it does not do

HSI, RGBW and color presets are not available in this version. No groups of lights, no firmware updates.

Not affiliated

LightDeck is an independent app. It is not affiliated with or endorsed by LUPO s.r.l. LUPO is a trademark of its owner and is used here only to say which lights the app works with.

Domande, segnalazioni di errori, un modello che si comporta in modo strano: scrivi a apps@kiusso.net. Se puoi, indica il modello della luce, la versione di iOS e che cosa ti aspettavi.

Domande frequenti

La mia luce non compare nell'elenco.

Controlla che la luce sia accesa e vicina all'iPhone e che il suo Bluetooth sia attivo. Tocca «Cerca luci» per ripetere la ricerca. Se un altro telefono o un'altra app è già collegato alla luce, questa può non comparire: una luce Bluetooth accetta una connessione alla volta. Se l'app dice che il firmware radio della luce è precedente alla 2.4.2, quella luce non si può comandare con LightDeck.

L'app dice che l'accesso al Bluetooth è disattivato.

Apri Impostazioni sull'iPhone, cerca LightDeck e consenti il Bluetooth. L'app ha un pulsante che porta lì. Controlla anche che il Bluetooth sia acceso nel Centro di Controllo.

Posso comandare più luci insieme?

No. LightDeck comanda una luce alla volta, quella a cui l'iPhone è collegato. Le luci già trovate restano in elenco, quindi puoi passare dall'una all'altra.

Mancano alcuni effetti.

Gli effetti dipendono dal modello. Le luci monocolore e bicolore ne hanno pochi o nessuno; i modelli a colori ne hanno di più. LightDeck mostra solo ciò che il modello dichiara di supportare.

Ho toccato «Passa a DMX» e la luce si è spenta.

È normale. In modo DMX la luce resta spenta finché non riceve un segnale DMX. Tocca «Torna a Bluetooth» e l'app rimanda l'ultima temperatura colore.

Modelli supportati

LightDeck riconosce i modelli LUPO della tabella dell'app ufficiale: Dayled, Superpanel, Actionpanel, Kickasspanel, Ultrapanel, Hyperpanel, Lupo LED e Movielight (300 e 600). Che cosa offre ogni modello (effetti, campo K, ventola, DMX) viene dalla stessa tabella.

Provata solo sulla Movielight 300 Dual Color. Sugli altri modelli dovrebbe funzionare, ma non è stata provata. Se ne hai uno e qualcosa non va, scrivimi.

Che cosa non fa

HSI, RGBW e colori preset non sono disponibili in questa versione. Niente gruppi di luci, niente aggiornamenti del firmware.

Nessuna affiliazione

LightDeck è un'app indipendente. Non è affiliata né approvata da LUPO s.r.l. LUPO è un marchio del suo proprietario e qui è usato solo per indicare con quali luci funziona l'app.